top of page

CoG - Hybrid Glucometer

Meet The World’s First Hybrid, Non-Invasive Glucometer

Medically Tested & Clinicly Proven.

CE Approved. FDA Pending

Trusted & Loved by Top Industry Experts

​

“… I must conclude that this is the most accurate performance of a non-invasive device technology for prediction of blood glucose that I have seen so far. In fact, this device represents a major improvement in non-invasive glucose prediction technologies!”. 

​

Prof. Andreas Pfützner, M.D.,Ph.D

From The Press

Read What Others Think About Us
Putting a fingure in testing device
New fingerprick-free glucose meter takes the “Ouch!” out of diabetes care

Today marks World Diabetes Day, a date chosen in tribute to Dr. Frederick Banting, co-discoverer of insulin, who was born on November 14, 1891.  While the discovery of insulin made survival with diabetes possible, the disease itself continues to spiral out of control around the world…

doing Glucose test and a plate having food in it
To Mark World Diabetes Day, Israeli Company Promotes Needle-Free Glucose Test

Today marks World Diabetes Day, a date chosen in tribute to Dr. Frederick Banting, co-discoverer of insulin, who was born on November 14, 1891.  While the discovery of insulin made survival with diabetes possible, the disease itself continues to spiral out of control around the world.

Holding a bag of blood
Ein Start-up aus Caesarea hat ein Gerät zur schmerzfreien Überprüfung des Blutzuckers entwickelt

Ein Diabetiker muss sich vier- bis fünfmal in den Finger stechen – jeden Tag, sein Leben lang. Mit dem Tropfen Blut misst er seinen Blutzuckerspiegel, um die nötige Menge des Insulins zu bestimmen. »Das sind oft mehr als 100.000-mal Schmerzen und Verletzungen«, sagt Andreas Pfützner vom »Pfützner Science und Health Institut« 

The Future Is Finally Here.

Measure Instantly. Anytime, Anywhere. Up to 90% Less Pricking.

Hybrid Non-invasive & Invasive device

Instant glucose and HbA1c measurement

A personalized device that constantly adjusts to your lifestyle

Better tracking of lifestyle factors can impact glucose level trends

Clinicly tested and CE approved

What Customers Say.

"... A few months ago, I have acquired the CoG device. At the beginning I had some problems with the device, but the company replaced it with a new one and it has been working wonderfully since. I monitor myself about 8 times a day and most of the time over 90% of my readings were pure non-invasive. When I started my HbA1c was 7.5%, a parameter the device also provides as an additional indication. After a few months of use, I started to improve my diet as I saw exactly what kind of food influenced my glucose level. Now my HbA1c is 6.2%. I compared my measurements at the hospital and it was 6.15%, which is amazing! "

​

Maria K. - Germany

attending a covid meeting.jpg

Get Your CoG Now & Stop the Constant Pricking Routine.

Please beware of counterfeit CNOGA Medical products from any other unauthorized websites!

How Does It Work?

Learn How The Magic Happens
  • HOW DOES IT WORK
    Four LED lights shine wavelengths from visual light to infrared light through the fingertip As the light wave pass through the fingertip, some of it is absorbed and the light signal is changed Next, a camera sensor detects the changed light signal in real time Using patented algorithms and a vast amount of data the device analyzes the correlation between the signal and the bio parameters
  • UNIQUE TECHNOLOGY
    Continuous, Non-invasive and Cuff-free Blood Pressure Non-invasive Hemoglobin, Hematocrit, and RBC Non-invasive Blood Gases (Ph, PCO2, PO2, O2&CO2 Content) Non invasive Cardiac Output , Stroke Volume, MAP Bluetooth – Cloud Connectivity
  • PARTS INCLUDED
    TensorTip is supplied with the following components: Battery charger Input: 100v~-240v~, 50Hz – 60Hz DC Output: 5v / 1300mA Stand/Finger Chamber cover Protective pouch Self-Test Arc User Manual
  • INSTRUCTIONS FOR DISINFECTION
    1. Washing your hands: Before using the device, wash hands thoroughly with warm water to prevent contamination and infections. Dry hands completely with the use of a clean towel. 2. Disinfection of hands: Apply 70% alcohol hand sanitizer and wait for alcohol to air dry. 3. Disinfecting the device before measuring: I. Open the lid of the fingertip compartment. II. Clean the finger compartment well with a 70% Isopropyl alcohol wipe (make sure the pad is moist, not soaked, to prevent the alcohol from permeating the device). Do not to touch the gel component with alcohol, only the plastic part. III. Wait for the alcohol to air dry. iv. Close the finger compartment. 4. After the measurement: Wipe with 70% Isopropyl alcohol moist wipes (pads) the entire device (inside and out) to prevent infections. Do not to touch the gel component with alcohol, only the plastic part.

FAQ

  • HOW DOES IT WORK
    Four LED lights shine wavelengths from visual light to infrared light through the fingertip As the light wave pass through the fingertip, some of it is absorbed and the light signal is changed Next, a camera sensor detects the changed light signal in real time Using patented algorithms and a vast amount of data the device analyzes the correlation between the signal and the bio parameters
  • UNIQUE TECHNOLOGY
    Continuous, Non-invasive and Cuff-free Blood Pressure Non-invasive Hemoglobin, Hematocrit, and RBC Non-invasive Blood Gases (Ph, PCO2, PO2, O2&CO2 Content) Non invasive Cardiac Output , Stroke Volume, MAP Bluetooth – Cloud Connectivity
  • PARTS INCLUDED
    TensorTip is supplied with the following components: Battery charger Input: 100v~-240v~, 50Hz – 60Hz DC Output: 5v / 1300mA Stand/Finger Chamber cover Protective pouch Self-Test Arc User Manual
  • INSTRUCTIONS FOR DISINFECTION
    1. Washing your hands: Before using the device, wash hands thoroughly with warm water to prevent contamination and infections. Dry hands completely with the use of a clean towel. 2. Disinfection of hands: Apply 70% alcohol hand sanitizer and wait for alcohol to air dry. 3. Disinfecting the device before measuring: I. Open the lid of the fingertip compartment. II. Clean the finger compartment well with a 70% Isopropyl alcohol wipe (make sure the pad is moist, not soaked, to prevent the alcohol from permeating the device). Do not to touch the gel component with alcohol, only the plastic part. III. Wait for the alcohol to air dry. iv. Close the finger compartment. 4. After the measurement: Wipe with 70% Isopropyl alcohol moist wipes (pads) the entire device (inside and out) to prevent infections. Do not to touch the gel component with alcohol, only the plastic part.
bottom of page